Fixed Cloned SSD Won't Boot

Amy Dennis

Jan 27, 2024 • Filed to: Take Data Backup • Proven solutions

The SSD may surprise you with multiple errors that you would find hard to deal with. Still, there is no need to panic, you can surely boot from SSD after clone. There are multiple ways to solve this error, which are mentioned in the guide. In this guide you will also have the reasons behind the issue of cloned SSD won't boot. You will also have a remarkable software to get your problem fixed. Getting aware of the error will enable you to tackle this problem in the future. So, follow the guide carefully to get yourself out of this devastating situation. You must understand the steps in detail.

Part 1: Why Cloned SSD won't boot?

If you are not aware of the causes of any problem, you certainly can't solve it properly. The same is the case with the cloned SSD won't boot error, you need to know all the possible reasons behind this problematic situation to tackle it in the future;

1. The source disk can't boot

The first and foremost reason behind this issue can be the source disk. The source disk can have bad sectors which usually results in these errors. One of the most prominent causes behind cloned SSD won't boot are the bad sectors of the source disk. However, if this is the reason behind your problem, no software can fix it.

2. Set the wrong drive to boot from

If you encounter the issue of cloned SSD won't boot. This can happen when you take out the source disk and attach it to any other computer. Once you have done that, you clone the source disk without booting from the source disk. In this procedure, many people face the issue of cloned SSD won't boot.

3. The SSD needs specific drivers

There are cases when the drivers that you have installed aren't suitable for the SSD. In this case, the reason can be that SSD needs some specific drivers to complete the procedure.

4. GPT/MBR conflict

There are a variety of conflicts that happen during any task of the computer. Primarily if GPT/MBR conflict takes place during the procedure, it can result in this issue.

5. Errors during the cloning process

If any error occurs during the cloning process, it can surely give you the error of cloned SSD won't boot.

6. Connect the SSD to a computer with a USB

The connection errors are also a culprit behind multiple errors. If you have connected the SSD to a computer with a USB, this issue can exist.

Part 2: How to make cloned SSD bootable?

Coming to the core section of the guide, several solutions can tackle this error. The first thing to understand is the reason behind your error. Every person has a different scenario, the solution of any problem depends entirely on the cause of it. Firstly, make sure you have detected the reason behind your error. Once you have done that, there are few methods which can help you out in this situation, follow them carefully;

Method 1: Set the correct drive to boot

If you have a computer and you want to clone its disk. You usually take out the disk from that computer and connect it to another. During this process, the error can occur. You need to set the source disk as the drive to boot. Follow the steps to do so;

Step 1: Turn on your PC.

Step 2: When the windows start to open, press F2/F12/DEL to enter the BIOS.

Step 3: Once you have done that, you need set to boot from the source disk.

In case, if the computer doesn't boot from the source disk, you can remove the old disk and replace it with the source disk.

Method 2: Correctly connect SSD to your computer

As mentioned before, the poor connection of SSD to your computer can also result in this error. You can check the connection of your SSD with the computer to solve the problem, follow the steps to do so;

Step 1: You need to get the SATA cable to connect the SSD to your computer. This issue usually occurs with USB.

Step 2: Connect the SSD with your computer using SATA cable. Make sure the connection is firm.

Method 3: Add necessary drives to the cloned SSD

Many SSD requires particular drivers to properly continue the booting process. You need to add the necessary drivers to the cloned SSD. Follow the steps to solve your problem;

Step 1: Get the SATA cable and connect your SSD to the computer using it. The SATA controller is usually embedded with the motherboard. In some cases, a SATA add-on card. The additional drivers are mostly prompt by SATA add-on cards.

Step 2: See, if the drive is recognized by the operating system.

Step 3: if it isn't recognized, you need a control device driver. However, you can use a SATA controller, if it is recognized during the setup without any special drivers, the completion of the installation can be done after the initial setup.

Step 4: You need to check for the driver updates from the operating system. While you install the windows with the DVD, the computer will ask you for the location of the installation. In case the SSD doesn't show up. Choose the load driver option.

Method 4: Restart the cloning process and fix the errors

If you are tired of all the above options. You surely need to restart the cloning process and fix the errors using AOMEI Backupper.

AOMEI Backupper

This is the most astonishing backup and restores software which contains all features of the Standard Edition, provides complete and reliable PC backup and restore strategies for any of the windows version. System Clone, Backup Scheme, Dynamic Disk Backup, Dissimilar Hardware Restore, Merge Images, etc. and many other diverse and useful features are available. Not only the backup, but the software allows you to an auto-sync USB drive when connected with File Sync. There are a vast number of functions that this software contains. You surely need to use this software to tackle the issue of cloned SSD won't boot, follow the steps;

Step 1: First of all, download and install AOMEI Backupper on your computer. Now, launch the software.

Step 2: Connect the SSD to your computer firmly. Furthermore, click on the option of Clone> Disk clone.

Step 3: Select your HHD as the source disk.

Step 4: In this step, choose your SSD as the destination disk.

Step 5: A new window will open up, tick the option of "SSD alignment" and start the process of cloning. This process might take up some time.

Method 5: Fix GPT/MBR conflict

As mentioned above in the reasons, the GPT/MBR conflict can also result in this error. Follow the steps to efficiently fix this conflict.

Step 1: confirm if you have an operating system with 64-bit. Secondly, make sure it allows UEFI mode.

Step 2: In case, your computer supports only legacy boot mode, you can convert GPT to MBR. Doing this can solve your problem and your disk can boot properly in legacy boot mode.

Conclusion

The issue of fixed clone SSD won't boot surely gives the users a hard time. however, the good part is that this issue is completely solvable. you just need to make sure that you follow the right steps and use the right software.