How to Fix Scanning and Repairing Drive Stuck in Windows 10

Theo Lucia

Nov 11, 2024 • Filed to: Answer Hard Drive Problems • Proven solutions

You can check faults such as bad sectors in Windows 10 OS using a unique feature. When this feature fails, Windows 10 computers will get stuck in booting or experience a delay. Scanning and repairing drive stuck at 10 is an error that some users have reported.

Booting gets stuck for even hours and it is the same thing when they power their computers. You should give it time. Although this process can complete when given time, the below options will help when you encounter the error in Windows 10. Below are 7 solutions you can use.

Part 1: About Scanning and Repairing Drive

Windows 10 stuck on repairing disk errors can be persistent when you try to boot your computer. Whether it is stuck for minutes or hours, this problem can be frustrating.

What causes the Windows scanning and repairing drive stuck problem and how is it fixed?

Below are the different reasons that could lead to this.

• The hard drive has bad sectors
• You forced the computer to shut down or there was a power outage
• The drivers are not well configured
• The PC has a virus

Besides that, there could be other reasons. We will look at 7 solutions to the scanning and repairing drive error.

Part 2: Fixed: Scanning and Repairing Drive C/D Stuck at 0%, 10%, 11%...100%

As the scanning process continues, you cannot use Windows. If you cannot wait, it is advisable you manually scan and repair the drive. The below instructions will help if you get the error during startup.

Before you resolve the scanning and repairing drive c stuck at 10 percent, backup your data. You will lose it if you don’t.

Method 1. Check the Disk Connection

Displaced computer disks also cause the scanning and repairing drive stuck error. Displacement leads to connection problems between the PC and the disk. To check if this is the problem, assess the port and the cable.

Method 2. Wait for the completion of the Scanning and Repairing Process

The level of issue in the drive determines how long the scanning and repairing drive stuck takes. It may take minutes or hours to complete depending on the issue. Giving it time is recommended as it will eventually work.

Method 3. Stop Windows from Scanning and Repairing the Drive

In the "automatic Repair," it is possible to disable the auto disk checking process. If you are pressing any key as Windows startups, you can ignore the scanning and repairing drive option. Below are the detailed steps to stop Windows from doing the scanning and repairing task.

Step 1. When you are stuck at scanning and repairing drive, you first need to shut down the PC. Press the power button.

Step 2. Next, start the PC. The "Preparing Automatic Repair" screen will show up and then you will see "Diagnosing your PC."

Step 3. You need to disable the disk checking before it starts. To do so, press on any key continuously or press "Ctrl+C."

Method 4. Disable Automatic Repair

Automatic Repair is known to bring issues such as an automatic Repair loop or Preparing Automatic Repair. It also causes scanning and repairing drive stuck at 11. To avoid such issues, you should disable it. By entering the Windows Installation Media, which is not available to many, you can disable the Automatic Repair option. You can also use the Windows Recovery Environment (WinRE).

Step 1. To shut down the computer, press and hold down the power button for about 10 seconds.

Step 2. Start the computer by pressing the power button and when you see the Windows logo, turn it off by pressing the power button. It will go off after 10 seconds.

Step 3. Again, start the computer by pressing down the power button. Just like you did in step two, here also you need to press the power button once Windows restarts to turn off the PC.

Step 4. After you press the power button, let it go up and you will see the PC in WinRE.

Step 5. You will see the "Choose an option" screen. Here, you need to go to the "Troubleshoot" section, then "Advanced Options," and finally "Command Prompt."

Step 6. Go ahead and enter "bcdedit." Under the Windows Boot Loader, take into account the values of "identifier" and "recovery enabled." This is "(current)" and "Yes."

Step 7. Here proceed to enter "bcdedit /set {current} recoveryenabled no." to disable Automatic Repair. In this case, the term ‘{current}’ represents the operating system used, and changing the value to no will disable Automatic Repair.

Step 8. In the final step, proceed to restart your computer.

Method 5. Enter Safe Mode and Run CHKDSK

To fix the windows 10 scanning and repairing drive stuck at 100 error, you can run CHKDSK in Safe Mode. This is a diagnostic mode that starts your PC with minimal drivers and services.

Step 1. To shut down the PC, press the power button for ten seconds.

Step 2. Start the computer by pressing the power button. When you see the Windows logo turn off the computer by pressing the power button for about 10 seconds.

Step 3. Now, press the power button to restart your computer. Turn it off when Windows start.

Step 4. Start the computer by pressing the power button for 10 seconds. Let it power up and you will see the PC in WinRE.

Step 5. Select "Troubleshoot" on the "Choose an option" screen. Now, head over to the "Advanced Options" section. There you will find the "Startup Settings" option. Finally, click "Restart."

Step 6. Once the computer has restarted, a list of options will be displayed. To active Safe Mode with Networking, press "F5" or "5."

Step 7. Click on "This PC." Proceed to right-click on the windows scanning and repairing drive stuck and then select "Properties."

Step 8. Select "Check" on the "Tools" tab. It is just like when you run CHKDSK in Command Prompt.

Step 9: Finally, you can start the scanning process by clicking the "Scan drive" option. An error checking box will pop-up on your screen. You should click on the "scan and repair drive" option and then follow the instructions.

Method 6. Run System Restore

If your computer has a system restore point, you can restore your computer to an earlier status. This is when you were not experiencing the Windows scanning and repairing drive stuck at 0 error. This is another way of fixing the problem. Below is a detailed procedure on how to go about it.

Step 1: To enter the Windows Recovery Environment, press, and hold the computer’s power button. You must force it to shut down 3 times.

Step 2: Proceed to select "Troubleshoot," then "Advanced options" and then the "System Restore" option.

Step 3: In the pop-up window that shows up, select "Next."

Step 4: Select one system restore point and then "Next."

Step 5: Go ahead and confirm your restore point and then click "Finish."

Reboot your PC confirm to confirm the issue is no longer there.

Method 7. Recover Data

You can now easily access your Windows computer after using the System Restore method mentioned above. If you perform a system restore, you may lose some of your data, especially due to bad sectors and drive corruption. However, you do not have to worry about the loss. Just perform the system restore.

Once you are done with the restoration, download Recoverit and launch it. It helps with data recovery in the hard drive. It recovers lost, deleted, and corrupted data from your hard drive.

Step 1: Install the Software

Download Recoverit, which is available for free. Launch it and continue.

Step 2: Choose the Drive

Your PC must detect the damaged hard drive first. On the hard drive, click on the location where the files were lost and scan the data by clicking "Start."

Step 3: Scanning the Drive

The software will start a basic search of the data. The data may not show but you can enter the "All-around Recovery" mode to search for more.

Step 4: Preview Files and Recover

Check on the scanning results to see the recoverable files. Besides previewing some of these files, you get them back by clicking on the "Recover" button.

With these steps, you recover data from an unreadable or damaged hard drive. If you get the scanning and repairing drive stuck at 10 percent issue, stop using the hard disk. To recover your lost data from a hard drive, use Recoverit.

Conclusion

If you get an error computer stuck on scanning and repairing drive, the disk has issues. You can opt for Windows to skip the errors or fix the disk issues. The decision you make depends on your issue. Recoverit is a specialized software that comes in handy during such issues.

This data recovery software program is known to be one of the best in the market. You can recover data from even a damaged hard drive with ease. You don’t have to stress about data loss. It also fixes the Windows 10 scanning and repairing drive stuck at 0 issues.